METRA Cab/Commuter Car #8726

Reduced
Florida
Price Reduced

Specifications

  • Listing ID: 18402034
  • Type: Coach Cars
  • Year: 1960
  • Manufacture: Pullman Standard
  • Bearing Type: Grease
  • Coupler Type: H
  • Operational: Yes
  • Self Contained: No
  • Length (feet): 85.00
  • Width (feet): 10.00
  • Height (feet): 15.00
  • Weight (tons): 70
  • Shipping (minimum):10,000
  • Can be shipped on own wheels, interchanges to CSX
  • Location: Florida
  • Price:
Contact us about this listing Login For More Photos, Pricing and Details Request Inspection

Full Specifications

METRA Cab/Commuter Car #8726

-- Located in Florida. Asking price: . --

  • Built 1960
  • Builder: Pullman Standard
  • Model: CA3B
  • C&NW #177

    The Gallery Car, also known as a Bi-level Car, is a passenger rail car that has two levels of passenger seating and is commonly used in mass transit or commuter lines all over the U.S., except the Northeast where tunnel and bridge clearances will not allow it. The large center door allowed for quickly loading and unloading passengers.  The cars were built with heating, air-conditioning, and lighting to be provided by head-end power from the locomotive, rather than from a generator on board the car itself. This saved space under the car and better accommodated the bi-level seating along with saving overall car weight. The open gallery design of the seating area not only increased seating capacity but also allowed the Conductor to make one pass through the car to be able to collect fares from passengers sitting on either the upper or lower levels. They were also designed for push-pull operation, with several cars being equipped with a Control Cab where an Engineer could run the train backwards without the need to switch the locomotive to the other end.  Some of the mechanical attributes include: Steel construction, grease bearings, HEP, electric heat, A/C, restroom,  push/pull cab (cab equipment intact), high capacity seating, serviceable wheels. Car does have some corrosion on side sheets.

     


Q-How much does it cost to ship a passenger car by truck?
The costs involved with shipping a passenger car will vary a bit depending on the type of car and the equipment the service provider has and of course the distance it must travel. Normally a passenger car will weigh between 60-85 ton, will be approx. 85' long, ten feet wide and approx. 13-15' high sitting on it's trucks (wheel assemblies). The safest method of shipping will be to lift the car off it's trucks and set one end of the car on the back of a semi truck and the other end of the car on a set of road dollies. So basically the car would be pulled down the highway like a trailer. The trucking company will need to make a second trip to pick up the trucks and deliver them to the site before the truck arrives with the car body. It is recommended that the car be set on a short piece of track since that is how the car structure was designed. You normally can find used railroad ties at landscaping companies and for rail we suggest contacting a local railroad museum, shortline railroad or scrap yard. On an average you can expect to spend a minimum of $10,000-$15,000+. The total price will depend on the trucking company and crane companies in the area. Shipping is the responsibility of the buyer and we are more than happy to discuss the project with any service provider so that fully understand the process. 

How much does it cost to ship a passenger car by rail? 
If a passenger car is capable of being shipped by rail, that does not mean that is the easiest or cheaper method of transport. If the final destination is off live rail then shipping by truck (see above paragraph) will be the best option. This way you know when it will show up and an in what condition it will be in. To ship a car by rail it will need to meet all mechanical and safety standards of the Federal Railroad Administration and the interchanging railroad. In most cases we can recommend a trusted independent inspector who can do an evaluation of the car for you and perform what work needs to be done. On average the car will need to have the air brakes recertified (approx. $5,000-$8,000). And it will need to have UMLER Tags and reporting marks installed on the side of the car (approx. $250.00 - $500.00). If the car is ready to be shipped in freight service (like a box car in a train) you will need to open an account with all railroads involved in the move and get a tariff for moving a passenger on it's own wheels (we can recommend several trusted contractors who can make all the shipping arrangements for you). The railroads charge between $5.00- $15.00 per mile, often the railroads don't go directly from point A to point B so you will need to pay the total amount of mileage the car will travel to get to the final destination. It is recommend that you have the car insured before shipment ( we can recommend several carriers who specialize insuring railroad equipment). 

How much does it cost to ship a car by railroad flat car? 
Occasionally a passenger car can't be shipped by rail due to it's physical attributes or shipping by truck is not the best option. You can ship a car loaded on a flat car, it will need to be secured to the flat car per American Association of Railroads tie down specifications. The tariff often can be cheaper than moving a car on it's own wheels, but you will still need to pay crane costs at origin and destination and you will need to have an active siding for the car to be delivered to. Shipping by flatcar will start at approximately $10,000 and will be based on origin and destination crane cost and the rail tariff and any car rental costs. 

Visit Our Advertisers


You May Also Like

We use cookies to ensure that we give you the best experience with our website. If you continue to use this site you agree you have accepted our privacy policy and other policies.. Accept